← Locksmith Knowledge Study

FREE STUDY · 6 MIN LESSON

The Code Desk: Bitting, Blind Codes & Depth-and-Space

Read this lesson without an account. To use narrated cards and save your progress in the app, create a free account or sign in. No payment is required for the free modules. Knowledge practice does not replace approved training or any skills evaluation your certifying body requires.

At the Code Desk

Check this point against current official guidance before relying on it.

  • A key code is the bitting — the cut depth at every position.
  • Codes let you originate a key with no original in hand.
  • Direct or blind, factory or restricted — the code desk decides.

What does a key CODE actually specify, and why does it matter?

Check this point against current official guidance before relying on it.

  • A key CODE specifies a key's bitting — the depth of cut at each position — so a key can be made without an original by cutting to code. Codes let a locksmith originate keys accurately. Cutting to code produces a cleaner key than copying a worn original. Remember: A code is the bitting — the cut depth at each position. It lets you originate a key with no original.

Direct code vs blind code — what is the difference?

Check this point against current official guidance before relying on it.

  • Codes are DIRECT (bitting) or BLIND/INDIRECT: a direct code states the actual cut depths, while a blind code must be translated to bitting using a code book or software. Blind codes protect security — the number on the lock means nothing until looked up in the manufacturer's code source. This is the classic Codes trap. Remember: DIRECT states the cuts. BLIND means nothing until you look it up in the code book. The classic trap.

What does a code machine do that a duplicator does not?

Check this point against current official guidance before relying on it.

  • A code machine cuts a key directly from its code (no original needed), using the manufacturer's depth-and-space (D&S) system for that keyway. Depth = how deep each cut is; space = the distance from the shoulder/tip to each cut position. The D&S system defines both for the keyway. Remember: It cuts straight from the code — no original needed — using the keyway's depth-and-space system.

What do code books and code software give you?

Check this point against current official guidance before relying on it.

  • Code books and code software translate blind codes into bitting and specify the D&S system, blank, and MACS for a keyway. The code source is the authority for originating a key — it tells you the cuts, the correct blank, and the spacing/depth increments. Remember: They translate a blind code to bitting and tell you the D&S system, the blank, and the MACS.

Factory code vs registered/restricted code — what changes?

Check this point against current official guidance before relying on it.

  • Codes may be FACTORY (assigned by the manufacturer, may be looked up) or REGISTERED/restricted (controlled, requiring authorization to obtain the bitting). Registered/restricted keyways add key control — the code and blanks are not freely available, which is a security feature. Remember: Factory codes can be looked up; registered codes need authorization. Restricted = key control.

Blind Is Not Direct

Check this point against current official guidance before relying on it.

  • A blind code does NOT state the cuts — you must look it up.
  • A code machine originates; a duplicator only copies.
  • Registered codes need authorization; factory codes can be looked up.

Sign Off the Job

Check this point against current official guidance before relying on it.

  • That is the Code Desk: Bitting, Blind Codes & Depth-and-Space brief.
  • Cards next — active recall locks it in.

Quick Self-Check

Check this point against current official guidance before relying on it.

  • Before the cards, answer in your head:
  • A lock has a number stamped on it but you cannot read cut depths from it. Is that a direct code or a blind code, and what do you need next?
  • Then check the explanation below.
  • Answer and explanation: A blind code needs an authorized code reference or manufacturer-approved system to interpret it. A direct code expresses the bitting rather than merely identifying a lookup entry.

Continue to narrated study — free account required →

What this course covers, sources and pricing →